News:

In case of emergency, please visit our Lifeboat Forum, Spare Goggles.

Main Menu

JB Weld brass to brass adhesion FAIL

Started by oldskoolpunk, January 03, 2013, 06:52:03 AM

Previous topic - Next topic

oldskoolpunk

I just had a total failure with JB Weld. I was trying to attach a piece of square brass stock about 1/4" on a side to a brass plate. I sanded both pieces until they were shiny, then roughed them up with a file. I mixed the two halves of JB Weld epoxy on a paper plate, and stirred them until they were a uniform grey. I then applied that to the material with a plastic knife, and clamped both pieces together with 3 C-clamps for 4 hours.

When I took off the C-clamps, the square brass stock fell off under its own weight, with no other load on it. It hadn't adhered at all.

I thought JB Weld worked on brass.  Apparently not.

What's good for a brass-to-brass joint?

Prof Marvel

My Good oldskoolpunk
I would recommend solder - hardware store "silver solder" is good for a very strong joint, but even hardware store soft or "plumbing solder" holds remarkably well.

Even if you do not have or cannot borrow a torch, one can cobble up an alcohol lamp and blowpipe to supply sufficient heat fro such a small joint.

yhs
prof marvel
MIGRATION to Spare Goggles under way

Argus Fairbrass

#2
I would say point number one you probably didn't leave it long enough for something of that weight. I've only used it on very light metals, such as a pair of broken sunglasses which are still fine. But heavy stuff I'd say you need to leave it for twelve hours minimum (you may want to go for twenty four if it's really heavy stuff).

Ensure it's spread evenly but thinly for the strongest bond, I even remember someone saying it'll set stronger if you gently heat it whilst curing. Soldering or brazing are certainly more recommended, but JB Weld is very good when it works properly, it's just a question of sussing it out a bit.
Have her steamed and brought to my tent!

Oneiros

I used it once many years ago. The process engineer (A chap called Richard) at the firm I work for came down from his ivory tower one day with his new packet of wonder material from across the pond... JB Weld.

I remember him proudly reading the packet to us, which stated that it could be used to repair many things among which was the engine block of a truck.

Unfortunatly, we then used it to hold a tiny piece of fiberglass to some MDF. Richard was confident that 6 hours curing time would be sufficiant as it was only a small piece of fiberglass, and not the engine block of a truck.

We then exposed it to 246 degrees centigrade of a solder reflow machine and watched his happy smile vanished. Oh happy days.  ;D
What really matters is what you do with what you have. - H. G. Wells

Narsil


Yeah JB weld needs a lot more cure time than 4 hours. 24 hours minimum, more in cold weather.

As well as sanding the surface it is important to clean it with alcohol or other degreaser to remove any grease or dust from the surface immediately before applying the adhesive. This step is absolutely vital on non-porous surfaces like metals.

Also JB weld is really a filler rather than an adhesive for the type of joint you describe a 2 part slow cure epoxy is ideal.






A man of eighty has outlived probably three new schools of painting, two of architecture and poetry and a hundred in dress.
Lord Byron

oldskoolpunk

Quote from: Narsil on January 03, 2013, 06:35:19 PM

Yeah JB weld needs a lot more cure time than 4 hours. 24 hours minimum, more in cold weather.

As well as sanding the surface it is important to clean it with alcohol or other degreaser to remove any grease or dust from the surface immediately before applying the adhesive. This step is absolutely vital on non-porous surfaces like metals.

Also JB weld is really a filler rather than an adhesive for the type of joint you describe a 2 part slow cure epoxy is ideal.

I got much better results with Devcon 5-minute epoxy. 

53Bash

Quote from: oldskoolpunk on January 03, 2013, 06:52:03 AMWhat's good for a brass-to-brass joint?

Solder, bronze brazing, or tig welding.  I've also used epoxy putties made by Kneadatite.  They have one that's a sort of coppery color.  They can cure in 4 hours IF nice and warm (a good halogen light will do), but overnight is better.  The guys's who make the original sculpts for "lead" gaming miniatures build armatures from brass wire and use these putties to do the actual sculpting, partly because (once hard) it holds up well against heat and chemicals used min mold making.

Dean Black

#7
TIG welding uses a non-consumable tungsten electrode to run a current through the metals being joined, and may or may not use a filler metal. Power source is constant-current DC or AC depending on metal used. This is good for thinner metal pieces up to 5mm thick. Its technique is sensitive in terms of timing & pressure handling, controlling the torch, feeding wire, it is usually done using an automated CNC (computer numerically-controlled). Since there isn't much information available online today covering the dangers of TIG welding I'm going to tell you
ALWAYS wear a proper face shield i.e. TIG welding helmet
ALWAYS wear close-toed shoes.
ALWAYS wear a long-sleeved, non-flammable shirt.
ALWAYS wear proper welding gloves.

jringling